Damp Proof Membrane(DPM) 1000 Gauge Black Per Roll
Polythene 60 Meters Lenght
Height 1 Meter or 3 Feet
Thickness 1000 Gauge
Colour black
KSh3,300.00
CompareDamp Proof Membrane(DPM) 1000 Gauge Black Per Roll 4 feet
Polythene 56 Meters Length
Height 4 Feet
Thickness 1000 Gauge
Colour black
KSh4,500.00
CompareDamp Proof Membrane(DPM) 1000 Gauge Clear Per Roll 4 feet
Polythene 56 Meters Roll
Height 4 Feet
Thickness 1000 Gauge
Colour Clear
KSh13,800.00
ComparePE Damp Proof Membrane 1.2 Meter by 50 Meters Virgin Material
PE Damp Proof Membrane 1.2 Meter by 50 Meters Virgin Material
PRODUCT DESCRIPTION
Comprises of 100 % closed cell low density polyethylene foam laminated with high-density polyethylene film.
Liner is designed to provide an easy to use moisture resistant membrane for use in concrete flooring.
The Liner is applied above or below a ground floor slab to stop ground
moisture reaching the upper surface of the floor. This product is used under a
floating floor as well as under a screed.
This combination is also resistant to mould, mildew, fungus and chemicals normally found in soil.
It not only has high compressive strength and a long life expectancy, it is extremely flexible and has an elongation break of over 40%
therefore they are able to deal with structural movement thus providing a long lasting damp proofing solution.
Key Benefits
Moisture barrier
Durable
Easy to handle
Resistant to puncture
Chemically stable
Application
It is designed as a low cost, easy to install solution to water storage, dams, porous soil or possible water table contamination.
For basements- it is applied in between the protected wall and a false wall of which the backfill is in contact.
For retaining structures- it is placed between the wall and the backfill.
It is however advised that soft sand is in contact with liner to avoid puncturing.
Waterways- The liner is placed at the bottom of the waterway while the cementitious layer covers and protects the liner.
KSh4,500.00
CompareRoof Heat Insulation Double Laminate 50 m by 1.2 m by 10 mm Thickness
Roof Heat Insulation
Length: 50 Meters
Width: 1.2 Meter
Thickness: 3 millimetre
Single side Silver laminate
Used for keeping homes, go-downs, warehouses and churches cool.
Regular home use the recommended size is 3 mm thickness
It is easily installed in one application creating a vapour barrier, thermal insulation, and will also achieve high acoustic values, reducing road, aircraft, and outside noise.
Procedure
For optimal insulation, ensure a minimum air gap of 25mm between the Jumbolene underlay and the iron sheets. The underlay maybe laid horizontally or vertically under the purlins.
One can use either strainer wires or Aluminium strips.Installation Guide for a New Roof:
1. Attach the galvanised wires onto the trusses running parallel to the purlins. The galvanised wires should be 300mm apart.
2. Place the roof insulation on top of the galvanised wires ensuring that the ends of the sheets are held firmly and that the sheets run continuously from one end of the truss to the other.
3. When adjoining the next roll, make sure that 100mm overlaps the first roll. This should ensure that the product is creating a vapour barrier.
4. Where necessary cut it around any penetrations making sure a tight fit to minimize openings.
Installation Guide for an Existing Roof:
1. Place the roof insulation between the purlin and the galvanised steel strip and screw it onto the purlins using 1 inch self tapping steel screws.
2. When fixing the roof insulation onto the subsequent purlin, pull the sheet so as to achieve a tight and firm fit free of sagging.
3. When adjoining the next roll, make sure that 100mm overlaps the first roll. This should ensure that the product is creating a vapour barrier.
4. Where necessary cut it around any penetrations making sure a tight fit to minimize openings.
KSh31,500.00
CompareRoof Heat Insulation Double Laminate 50 M x 1.2 M by 2 mm Thickness
Roof Heat Insulation
Length: 50 Meters
Width: 1.2 Meter
Thickness: 2 millimetre
Double side Silver laminate
Used for keeping homes, go-downs, warehouses and churches cool.
Regular home use the recommended size is 3 mm thickness
It is easily installed in one application creating a vapour barrier, thermal insulation, and will also achieve high acoustic values, reducing road, aircraft, and outside noise.
Procedure
For optimal insulation, ensure a minimum air gap of 25mm between the Jumbolene underlay and the iron sheets. The underlay maybe laid horizontally or vertically under the purlins.
One can use either strainer wires or Aluminium strips.Installation Guide for a New Roof:
1. Attach the galvanised wires onto the trusses running parallel to the purlins. The galvanised wires should be 300mm apart.
2. Place the roof insulation on top of the galvanised wires ensuring that the ends of the sheets are held firmly and that the sheets run continuously from one end of the truss to the other.
3. When adjoining the next roll, make sure that 100mm overlaps the first roll. This should ensure that the product is creating a vapour barrier.
4. Where necessary cut it around any penetrations making sure a tight fit to minimize openings.
Installation Guide for an Existing Roof:
1. Place the roof insulation between the purlin and the galvanised steel strip and screw it onto the purlins using 1 inch self tapping steel screws.
2. When fixing the roof insulation onto the subsequent purlin, pull the sheet so as to achieve a tight and firm fit free of sagging.
3. When adjoining the next roll, make sure that 100mm overlaps the first roll. This should ensure that the product is creating a vapour barrier.
4. Where necessary cut it around any penetrations making sure a tight fit to minimize openings.
KSh11,500.00
CompareRoof Heat Insulation Single Laminate 50 m by 1.2 m by 5 mm Thickness
Roof Heat Insulation
Length: 50 Meters
Width: 1.2 Meter
Thickness: 5 millimetre
Single side Silver laminate
Used for keeping homes, go-downs, warehouses and churches cool.
Regular home use the recommended size is 3 mm thickness
It is easily installed in one application creating a vapour barrier, thermal insulation, and will also achieve high acoustic values, reducing road, aircraft, and outside noise.
Procedure
For optimal insulation, ensure a minimum air gap of 25mm between the Jumbolene underlay and the iron sheets. The underlay maybe laid horizontally or vertically under the purlins.
One can use either strainer wires or Aluminium strips.Installation Guide for a New Roof:
1. Attach the galvanised wires onto the trusses running parallel to the purlins. The galvanised wires should be 300mm apart.
2. Place the roof insulation on top of the galvanised wires ensuring that the ends of the sheets are held firmly and that the sheets run continuously from one end of the truss to the other.
3. When adjoining the next roll, make sure that 100mm overlaps the first roll. This should ensure that the product is creating a vapour barrier.
4. Where necessary cut it around any penetrations making sure a tight fit to minimize openings.
Installation Guide for an Existing Roof:
1. Place the roof insulation between the purlin and the galvanised steel strip and screw it onto the purlins using 1 inch self tapping steel screws.
2. When fixing the roof insulation onto the subsequent purlin, pull the sheet so as to achieve a tight and firm fit free of sagging.
3. When adjoining the next roll, make sure that 100mm overlaps the first roll. This should ensure that the product is creating a vapour barrier.
4. Where necessary cut it around any penetrations making sure a tight fit to minimize openings.
KSh18,000.00
Compare
Roof Insulation 3mm Thickness
Roof Heat Insulation
Length: 50 Meters
Width: 1.2 Meter
Thickness: 3 millimeter
Double side Silver laminate
Used for keeping homes, go-downs, warehouses and churches cool.
Regular home use the recommended size is 3 mm thickness
It is easily installed in one application creating a vapour barrier, thermal insulation, and will also achieve high acoustic values, reducing road, aircraft, and outside noise.
Procedure
For optimal insulation, ensure a minimum air gap of 25mm between the Jumbolene underlay and the iron sheets. The underlay maybe laid horizontally or vertically under the purlins.
One can use either strainer wires or Aluminium strips.Installation Guide for a New Roof:
1. Attach the galvanised wires onto the trusses running parallel to the purlins. The galvanised wires should be 300mm apart.
2. Place the roof insulation on top of the galvanised wires ensuring that the ends of the sheets are held firmly and that the sheets run continuously from one end of the truss to the other.
3. When adjoining the next roll, make sure that 100mm overlaps the first roll. This should ensure that the product is creating a vapour barrier.
4. Where necessary cut it around any penetrations making sure a tight fit to minimize openings.
Installation Guide for an Existing Roof:
1. Place the roof insulation between the purlin and the galvanised steel strip and screw it onto the purlins using 1 inch self tapping steel screws.
2. When fixing the roof insulation onto the subsequent purlin, pull the sheet so as to achieve a tight and firm fit free of sagging.
3. When adjoining the next roll, make sure that 100mm overlaps the first roll. This should ensure that the product is creating a vapour barrier.
4. Where necessary cut it around any penetrations making sure a tight fit to minimize openings.
KSh15,000.00
Compare
Tactile Stone Coated Barge Box
SPECIFICATION
Size – 2000 mm
Fire resistant
Rain resistant
Noise resistant
Wind resistant
Light weight
Cost effective
Made In Kenya
50 Year Warantee
Tactile Barge Box is available across a range of 18 different colours.
KSh1,200.00
CompareTactile Stone Coated Steel Roofing Tile Classic Profile
Stone coated steel roofing tile Classic Profile. A traditional and attractive 8-tile roof panel with a timeless effect.
PROFILE
Classic Profile is designed to get the same appearance of the traditional clay roof style, with the additional benefits of steel roofing.
TACTILE’s Classic profile stands out from the rest of the classic profiles out there in the market. The stone coated steel roofing tile is designed to perfection giving it a fine blend of the traditional roof look whilst taking advantage of the highly durable quality of the steel alloy and Italian stone chips. The qualities of the Tile profile ensure it is second to none in the industry. This profile boasts seven perfectly designed valleys to help both the aesthetics and technical properties of a top quality roof. Aside from its interlocking characteristic, ensuring it is watertight; TACTILE’s profiles can withstand the most testing weather conditions. We redefine roofing solutions at TACTILE..
INSTALLATION
Classic eight tile panels can be interlocked either right over left or left over right with the side laps of one small corrugation. The panels are placed onto battens spacing 368 mm.
The down-turned front edge and the upturned rear edge of each tile provides a strong, weatherproof, overlapping and interlocking roof covering.
Each panel is secured by 4 nails in the front-down-turned edge into the side of the batten, positioned out of the water course.
SPECIFICATION
Panel Size – 420 mm x 1340 mm
Installed Exposure – 370 mm x 1265 mm
Panels Per Square Meter – 2.13 Square Meter
Installed Weight – 5.96 Kilograms per square meter
Fire resistant
Rain resistant
Noise resistant
Wind resistant
Light weight
Cost effective
Made In Kenya
50 Year Warantee
Tactile Roofing is available in four different profiles across a range of 18 different colours.
KSh735.00
CompareTactile Stone Coated Steel Roofing Tile Edge Profile
Stone coated steel roofing tile Edge Profile.
EDGE PROFILE
TACTILE’s Edge profile stands out from the rest of the classic profiles out there in the market. The stone coated steel roofing tile is designed to perfection giving it a fine blend of the traditional roof look whilst taking advantage of the highly durable quality of the steel alloy and Italian stone chips. The qualities of the Tile profile ensure it is second to none in the industry. This profile boasts seven perfectly designed valleys to help both the aesthetics and technical properties of a top quality roof. Aside from its interlocking characteristic, ensuring it is watertight; TACTILE’s profiles can withstand the most testing weather conditions. We redefine roofing solutions at TACTILE.
SPECIFICATION
Panel Size – 420 mm x 1340 mm
Installed Exposure – 370 mm x 1265 mm
Panels Per Square Meter – 2.13 Square Meter
Installed Weight – 5.96 Kilograms per square meter
Fire resistant
Rain resistant
Noise resistant
Wind resistant
Light weight
Cost effective
Made In Kenya
50 Year Warantee
Tactile Roofing is available in four different profiles across a range of 18 different colours.
KSh735.00
CompareTactile Stone Coated Steel Roofing Tile Shake Profile
Stone coated steel roofing tile Shake Profile.
SHAKE PROFILE
TACTILE’s Shake profile offers the best of both. For the wooden shake roof look coupled with the highly durable qualities of the light weight steel alloy, the Shake profile is your product. Unlike the wood characteristics, the Shake profile at TACTILE ensures that aesthetically you obtain your goal whilst simultaneously taking full advantage of the fire resistant qualities. The Shake profile is also a lot easier to maintain than the traditional wooden shakes making your roof look brand new for years to come. There are several colours available in the Shake profile no longer limiting you to the natural colour of the wooden shakes currently in the industry. So go on get that wooden feel with TACTILE’s top quality Shake profile.
SPECIFICATION
Panel Size – 410 mm x 1375 mm
Installed Exposure – 370 mm x 1335 mm
Panels Per Square Meter – 2.02 Square Meter
Installed Weight – 5.65 Kilograms per square meter
Fire resistant
Rain resistant
Noise resistant
Wind resistant
Light weight
Cost effective
Made In Kenya
50 Year Warantee
Tactile Roofing is available in four different profiles across a range of 18 different colours.
KSh735.00
Compare